In this article below you can locate a lot of very good resources relating to How to Install a Bathtub.
Mounting a bathtub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily obtainable, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the brand-new one. Ensure you have actually qualified yourself for the work and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This write-up will assist you mount a new tub in your shower room if you have actually currently purchased a brand-new bathtub and don't need to transform the setup of your previous supply of water pipelines.
Your devices and also material checklist must consist of the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the limited access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the tub in the required setting. The wooden boards are practical in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reads level.
To mount taps, fit all-time low of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leaks and tighten them if required. Load the bath tub and also inspect the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and sealing around the bathtub ought to wait up until the bathtub has been utilized a minimum of when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in area in between the tap as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, leading to issues with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our excerpt about How to Install a Bathtub. Many thanks for taking a few minutes to browse our posting. Sharing is good. Helping others is fun. Many thanks for your time. Kindly stop by our site back soon.
Article